BMW Werkz banner
1 - 20 of 22 Posts

· Registered
Joined
·
1 Posts
Discussion Starter · #1 ·
Helpppp!!! Pleassse!!!! I just bought some new Eibach Springs for all four tires! The Springs Drop 1.5 in Front and 1 in in rears. But the rears are way too low! I am thinking about putting those coil spring adjusters that they sell at Pep Boys and Auto Zone, but I am not sure if that will mess up the springs in the rear or even the whole suspension! I have m3 tires in the back which is wider and they are starting to rub. I don't have the money to buy new Springs. Will the Coil spring adjusters work, will it not compress right?? I just need it to raise up a little more!
 

· Registered
Joined
·
84 Posts
I know that by going to a lower suspension that you will have to adjust your fenders by rolling them and making them bigger. i know this is the case for the front but I'm not sure about the rear, hopefully some of the other guys here with more experience can add some insight to your situation.
 

· Premium Member
Joined
·
14,769 Posts
Why not put your factory rear springs in? That's a much better solution than putting in pepboys blocks in ... the only other solution is to get rear coilover type spring adjusters, but honestly, those wont be too much thinner than an inch, so you might as well put the stockers back in.
 

· Ich bin der Modifikator
Joined
·
3,190 Posts

· Registered
Joined
·
258 Posts
What M wheels do you have? What size? I just put M-Contours staggered on my 328i with no issues......& my rear was lowered 1" with H&R Sport Springs!

Where exactly are they rubbing......

You can try using a thicker upper rear spring pad, TMS carries them:

they actually come in these sizes 15mm, 10mm, 7.5mm & 5mm

Turner Motorsport - Item# 33531094754 / 33*53*1*094*754 - 15mm Rear Spring Pads (pair) - E36 E46


jb
so your rear rims are 9" wide? how do they not stick out past the fender?:conf
 

· Premium Member
Joined
·
14,769 Posts
Contours are 8.5 wide in the back, 7.5 front ... et41 both.

I have 235/40 all around on DS2s (same sizing) and I don't think i could squeeze a 245 back there without rolling fenders. (See sig)
 

· Registered
Joined
·
258 Posts
nice, i had m3 rims on and could not accelerate as they would squat on the tires. i had to feather the clutch to get back to the shop to take the rims off, but they were 9" wide in the rear. i now run 245 40 18 in the back on 8" rims. thanks Torque!
 

· Ich bin der Modifikator
Joined
·
3,190 Posts
Contours are 8.5 wide in the back, 7.5 front ... et41 both.

I have 235/40 all around on DS2s (same sizing) and I don't think i could squeeze a 245 back there without rolling fenders. (See sig)
I am running 245/40/17's in the rear, 41 offset no rubbing what so ever!



jb :)
 

· Ich bin der Modifikator
Joined
·
3,190 Posts
You got a side shot/upclose shot?
Here are some shots of Rear fitment M-Contours 17x8.5 41 offset..... Tires 245/40/17's.....






 

· Ich bin der Modifikator
Joined
·
3,190 Posts
Yeah I'm definitely too low for that.
Yeah......you are.......but he said he lowered about an inch with Eibach Sport Springs, I can't see him having a problem......I am lowered with H&R Sport Springs......1.5" in the front & 1.0" in the rear. :conf



jb :)
 
1 - 20 of 22 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top